CAT Articulated Truck 725 Specifications Page 60
- Page / 63
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
SEBU8524 161
Maintenance Section
Transfer Gear Oil Level - Check
2. Remove the oil fi
lter with a strap type wrench.
Discard the used oil filter properly.
Refer to Opera
tion and Maintenance Manual, “Oil
Filter - Inspect”.
3. Clean the oil
filter base.
4. Apply a thin coat of oil to the seal of the new oil
filter.
5. Install the new oil filter by hand. When the seal
contacts th
eoilfilter base, turn the oil filter by 270°
more. This will tighten the oil filter sufficiently.
i03581442
Transfer Gear Oil Leve l - Chec k
SMCS Code: 3159-535-FLV; 3159-535-OC
NOTICE
Care must be taken to ensure that fl uids are contained
during performance of inspection, maintenance, test-
ing, adj
usting and repair of the product. Be prepared to
collect the fluid with suitable containers before open-
ing any compartment or disassembling any compo-
nent co
ntaining fluids.
Refer to Special Publication, NENG2500, “Caterpillar
Dealer
Service Tool Catalog” for tools and supplies
suitable to collect and contain fluids on Caterpillar
products.
Dispose of all fluids according to local regulations and
mandates.
Chec
k the oil level before the engine is started.
1. Park the machine on a level surface. Engage the
park
ing brake and lower the truck body or OEM
attachment.
2. Rai
se the hood. Refer to Operation and
Maintenance Manual, “Hood Control”.
g01125860
Illustration 229
3. Wipe oil filler cap (1) and oil filler tube (2).
Note: The oil level dipstick is integral with the oil filler
capforthetransfergear.Oilfiller tube (2) for the
transfer gear is located on the left side of the engine
compartment.
4. Turn the handle on the oil level dipstick in order to
remove the dipstick. Remove the o il level dipstick.
5. Clean the dipstick by wiping.
6. Install the dipstick fully.
7. Remove the dipstick.
g00740112
Illustration 230
Note: The oil level dipstick is marked: “MIN COLD”
(3) , “MIN HOT” (4), and “MAX HOT” (5).
8. Check the oil on the dipstick.
Note: The engine can be started if the oil is above
the mark “MIN COLD”(3).
9. If necessary, add oil through filler tube (2) until
the level is at the “MIN COLD” mark. Refer to
Operation and Maintenance Manual, “Lubricant
Viscosities”.
- MAINTENANCE INTERVALS 1
- Operation and 2
- Maintenance 2
- Maintenance Interval Schedule 3
- Autom atic Lubrication Grease 5
- Tank - Fill 5
- (If Equipped) 5
- Grease Recommendations 6
- Backup Alarm - Test 7
- Battery - Recycle 7
- Battery or Battery Cable 7
- Inspect/Replace 7
- Body Pivot Bearings 8
- Brake Pads - Check 9
- Brake System Air - Pu rge 10
- Braking System - Test 11
- Illustration 126 12
- Illustration 127 12
- Illustration 128 12
- Circuit Breakers - R eset 13
- Cooling System Coolant (ELC) 13
- Illustration 131 14
- Illustration 132 14
- Illustration 130 14
- Coo ling System Coo lant 15
- Extender (ELC) - Add 15
- - C heck 15
- Illustration 135 16
- Illustration 137 17
- Illustration 138 17
- Cranksh aft Vibration Dam per 18
- - Change 19
- Level - C h eck 20
- Illustration 146 21
- Inspect/Repl 22
- Engine Air Filter Primary 23
- Element-C 23
- Engine Air Filte r Secon dary 24
- Element - Replac e 24
- Engine Cran kcase Breather 24
- Engine Oil L evel - Ch eck 25
- Engine Oil Sampl e - Obtain 25
- Illustration 156 28
- Illustration 157 28
- Illustration 158 28
- Engine Valve L ash - Check 29
- Ether Starting Aid Cylinder 30
- (OEM Attachmen t if Equipped) 30
- Front Frame 31
- Front Suspension Frame 31
- Oscillating Hitch 31
- Rear Frame 32
- Rear Frames 32
- Dump Body 32
- Radiator Mounts 32
- Mounts for the Suspension 32
- Fuel Sy stem 33
- Fuel System Primary Filter 34
- Illustration 170 35
- Illustration 171 35
- Fuel Syst 36
- Fuel Tank Cap and Strainer 36
- Fuel Tank Water and Sediment 37
- Fuses - Re place 38
- Hoist C ylinder Bearing s 39
- Lubricate 39
- Illustration 178 40
- Illustration 179 40
- Illustration 180 40
- Hydrauli 41
- Hydraulic System Oil Level 42
- Hydrau lic System Oil Samp le 43
- Hydrau lic Tank Breat her 43
- Clean/Inspect/Replace 43
- Hydrau lic Tank Strainer 44
- Clean/Insp ec 44
- Oscillating Hi tch - Ad just 44
- Oscillating Hitch - Lubricate 45
- Radiator Core - Clea n 46
- Refrig erant Dryer - Replace 47
- Rollover Protective Structure 47
- (ROPS) - Inspect 47
- Seat Belt - Insp ect 49
- Seat Belt - Replace 49
- Secondary Steering - Test 49
- Steering Cylinder Bearings 50
- Suspension System - Check 51
- Suspension and Su spen sion 51
- Cylinder Bear 51
- Tire Inflation - Ch eck 52
- Torque Converter and 52
- Transmission O il - Change 52
- Illustration 213 53
- Illustration 214 53
- Illustration 215 53
- Ecology Dr ain 54
- Transmission 55
- Oil Filter 55
- Oil Level 56
- Torque Con 57
- Transmission O il S ample 57
- Illustration 224 58
- Illustration 225 58
- Tran sfer G ear Oil Filter 59
- Illustration 230 60
- Illustration 229 60
- Transfer Gear Oil Samp le 61
- Illustration 232 62
- Illustration 233 62
- Illustration 234 62
- Windows - Clean 63
Related products and manuals for Cars CAT Articulated Truck 725
Cars CAT 735 User Manual
(20 pages)
(20 pages)
Cars CAT Articulated Truck 730 User Manual
(28 pages)
(28 pages)
Cars CAT Articulated Truck 730 User Manual
(16 pages)
(16 pages)
Cars Cat Wheel Loader User Manual
(28 pages)
(28 pages)
Cars Cat Articulated Truck 730 User Manual
(20 pages)
(20 pages)
Cars Cat Articulated Truck 725 User Manual
(20 pages)
(20 pages)
Cars Cat Articulated Truck 740 User Manual
(20 pages)
(20 pages)
Cars Cat 735 User Manual
(20 pages)
(20 pages)
© 2020, manymanuals.com. All rights reserved. | 0.450 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals