CAT Articulated Truck 725 Specifications Page 51
- Page / 63
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
152 SEBU8524
Maintenance Section
Suspension System - C heck
i02021470
Suspension System - Check
SMCS Code: 7200-535
The suspension system may drop the machine
suddenly leaving no clearance between the axle
housing, ma
in frame, tires, and mud guards.
Working in these areas can result in personal in-
jury or dea
th by crushing.
Park the machine on le vel ground and block the
front fram
e before you go under the machine.
1. Disengage the differential locks. Bring the
machine t
oagentlestoponfirm level ground.
2. Release the service brake. Wait for one second
before a
pplying the parking brake.
3. Install suitable stands under the front frame.
g01043895
Illustration 209
4. Measure distance (A). Distance (A) is the distance
between the mounting pins of the suspension
cylinder. Dimension (A) should be 700 ± 10 mm
(27.6 ± 0.39 inch).
Note: Measure distance (A) when the machine is
cool.
5. If the suspension height is not correct, consult your
Caterpillar dealer. Special tools and procedures
are required in order to adjust the height of the
front suspension.
6. Remove the stands.
i03581325
Suspension and Su spen sion
Cylinder Bear
ings - Lu bricate
SMCS Code: 7200-086-BD; 7201-086-BD
NOTICE
Check that the lines attached to all the remote grease
fittings are undamaged. If the grease lines are split,
grease will not reach the components that require lu-
bricating. Machine damage will result.
Park the machine on a level surface. Engage
the parking brake. Lower the truck body or OEM
attachment and shut off the engine. Install the
steering frame lock. Refer to Operation and
Maintenance Manual, “Steering Frame Lock”.
If regular lubrication is performed at the recommended
intervals, only one or two shots of grease will be
required at each fitting.
1. Clean all the fittings by wiping before you lubricate
the fittings.
Note: The fittings are located behind caps which
requireremovinginordertoaccessthefittings.
g01126573
Ill
ustration 210
2. Lubricate the front suspension cylinder bearings
thr
ough fittings (1). Lubricate the spherical bearing
on the front suspension a-frame through fitting (2).
No
te: The fittings for lubrication of the front
suspension are located at the rear of the tractor on
the left side.
- MAINTENANCE INTERVALS 1
- Operation and 2
- Maintenance 2
- Maintenance Interval Schedule 3
- Autom atic Lubrication Grease 5
- Tank - Fill 5
- (If Equipped) 5
- Grease Recommendations 6
- Backup Alarm - Test 7
- Battery - Recycle 7
- Battery or Battery Cable 7
- Inspect/Replace 7
- Body Pivot Bearings 8
- Brake Pads - Check 9
- Brake System Air - Pu rge 10
- Braking System - Test 11
- Illustration 126 12
- Illustration 127 12
- Illustration 128 12
- Circuit Breakers - R eset 13
- Cooling System Coolant (ELC) 13
- Illustration 131 14
- Illustration 132 14
- Illustration 130 14
- Coo ling System Coo lant 15
- Extender (ELC) - Add 15
- - C heck 15
- Illustration 135 16
- Illustration 137 17
- Illustration 138 17
- Cranksh aft Vibration Dam per 18
- - Change 19
- Level - C h eck 20
- Illustration 146 21
- Inspect/Repl 22
- Engine Air Filter Primary 23
- Element-C 23
- Engine Air Filte r Secon dary 24
- Element - Replac e 24
- Engine Cran kcase Breather 24
- Engine Oil L evel - Ch eck 25
- Engine Oil Sampl e - Obtain 25
- Illustration 156 28
- Illustration 157 28
- Illustration 158 28
- Engine Valve L ash - Check 29
- Ether Starting Aid Cylinder 30
- (OEM Attachmen t if Equipped) 30
- Front Frame 31
- Front Suspension Frame 31
- Oscillating Hitch 31
- Rear Frame 32
- Rear Frames 32
- Dump Body 32
- Radiator Mounts 32
- Mounts for the Suspension 32
- Fuel Sy stem 33
- Fuel System Primary Filter 34
- Illustration 170 35
- Illustration 171 35
- Fuel Syst 36
- Fuel Tank Cap and Strainer 36
- Fuel Tank Water and Sediment 37
- Fuses - Re place 38
- Hoist C ylinder Bearing s 39
- Lubricate 39
- Illustration 178 40
- Illustration 179 40
- Illustration 180 40
- Hydrauli 41
- Hydraulic System Oil Level 42
- Hydrau lic System Oil Samp le 43
- Hydrau lic Tank Breat her 43
- Clean/Inspect/Replace 43
- Hydrau lic Tank Strainer 44
- Clean/Insp ec 44
- Oscillating Hi tch - Ad just 44
- Oscillating Hitch - Lubricate 45
- Radiator Core - Clea n 46
- Refrig erant Dryer - Replace 47
- Rollover Protective Structure 47
- (ROPS) - Inspect 47
- Seat Belt - Insp ect 49
- Seat Belt - Replace 49
- Secondary Steering - Test 49
- Steering Cylinder Bearings 50
- Suspension System - Check 51
- Suspension and Su spen sion 51
- Cylinder Bear 51
- Tire Inflation - Ch eck 52
- Torque Converter and 52
- Transmission O il - Change 52
- Illustration 213 53
- Illustration 214 53
- Illustration 215 53
- Ecology Dr ain 54
- Transmission 55
- Oil Filter 55
- Oil Level 56
- Torque Con 57
- Transmission O il S ample 57
- Illustration 224 58
- Illustration 225 58
- Tran sfer G ear Oil Filter 59
- Illustration 230 60
- Illustration 229 60
- Transfer Gear Oil Samp le 61
- Illustration 232 62
- Illustration 233 62
- Illustration 234 62
- Windows - Clean 63
Related products and manuals for Cars CAT Articulated Truck 725
Cars CAT 735 User Manual
(20 pages)
(20 pages)
Cars CAT Articulated Truck 730 User Manual
(28 pages)
(28 pages)
Cars CAT Articulated Truck 730 User Manual
(16 pages)
(16 pages)
Cars Cat Wheel Loader User Manual
(28 pages)
(28 pages)
Cars Cat Articulated Truck 730 User Manual
(20 pages)
(20 pages)
Cars Cat Articulated Truck 725 User Manual
(20 pages)
(20 pages)
Cars Cat Articulated Truck 740 User Manual
(20 pages)
(20 pages)
Cars Cat 735 User Manual
(20 pages)
(20 pages)
© 2020, manymanuals.com. All rights reserved. | 0.278 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals